Δίκτυα Πληροφορικής

**Fluke Networks LinkIQ™ Cable + Network Tester** **Fluke NetworksThe LinkIQ™ Cable+Network Tester** is the testing solution to verify cable performance up to 10 Gb/s and solve network connectivity problems. **LinkIQ** validates cable performance using frequency-based measurements and provides distance to fault information along with a wire map of the cable under test. The **LinkIQ** also performs nearest switch diagnostics to identify key network issues and validate switch configuration eliminating the need of using another device. Additional features include Analog and Digital Toning, Port Blink, 802.1x authentication, Remote Office Locators, and the ability to manage results via LinkWare™ PC. The **LinkIQ™** is capable of measuring lengths up to 1000 feet (305 m) and provides distance to faults such as opens, shorts, and unterminated cable. Using the remote ID allows for a complete wire map of the cable pairs which helps identify miswired and split pairs. The primary cable testing feature of **LinkIQ™** is the cable performance test which qualifies the cabling bandwidth from 10BASE-T to 10GBASE-T (10 Mb/s up to 10 Gb/s). It performs these tests via frequency-based measurements. Using IEEE-standards-based measurements ensures that tested links meet performance requirements as opposed to transmission testers which only prove that the specific test devices can communicate over the link. **Key Features & Specifications**: - Generates Analog or Digital tones compatible with the IntelliTone™ Probe or Pro3000™ to assist in locating cables in a wall or telecommunications room - Blink Port light on switch to help identify the connected switch port - Compatible with MicroScanner™ PoE Remote Identifiers for Ethernet outlet identification - Touch Sensitive gesture-based color display - Rechargeable Li-Ion battery - RJ45 Port - PASS/FAIL frequency-based measurement results - Length measurement shows distance to termination, open or short - Wiremap shows type and location of fault (miswires, split pairs, shorts, breaks) - USB-C port for data export, software updates and charging - Cable “Speedometer” provides bandwidth information up to 10G - Save up to 1000 test results on the unit and export to LinkWare™ PC

**IMS - LANTIME M1000: Time and Frequency Synchronization Platform in 1U Rackmount-Enclosure** The 1U chassis has two power supply slots, optional two clock module slots, a CPU slot and four (three in case of a second reference clock) slots for additional input and output modules. Adding a second clock module and a second power supply transforms the IMS - M1000 into a fully redundant solution. Both, wide range AC and a 20-60 V DC power supply model can be mixed and matched as required. **Key Features**: - Optimized space usage - Synchronization of NTP and SNTP compatible clients - Web-based status and configuration interface (Demo), and console-based graphical - configuration utility - IMS - Intelligent Modular System platform - Up to 4 PTP (IEEE 1588-2008) modules - Redundant power and receiver option (eg GPS / GLONASS combination) - Hot Plug - Arbitrary combinations of modules - Meinberg's LANTIME time server is available with a variety of additional output options: IRIG Time Code, frequency synthesizer and programmable pulse outputs illustrate some of the many expansion options for your NTP server - Up to 16 additional LAN ports

**LANTIME M200: Compact NTP Time Server with integrated Reference Clock** LANTIME M200 time servers can be installed to provide accurate time to small and medium sized computer networks. This entry level time server synchronizes all systems either NTP- or SNTP-compatible utilizing a built-in MEINBERG radio clock as its primary reference time source. A stable and precise oscillator is capable of bridging interferences or a temporary loss of reception. **Key Features**: - Synchronization of IEEE1588-2008 (PTPv2) compatible clients electable Reference Sources: -GPS: Satellite receiver for the Global Positioning System -GNS: Combined GPS/GLONASS/Galileo/BeiDou satellite receiver (L1 frequency band), can also be used for mobile applications -PZF: DCF77 correlation receiver for middle europe -MSF: Long wave receiver for Great Britain -WWVB: Long wave receiver for the US time signal - Synchronization of NTP and SNTP compatible clients - Web-based status and configuration interface (Demo) and console-based graphical configuration utility - Supported net protocols: IPv4, IPv6, NTP, (S)NTP, DAYTIME, DHCP, HTTP, HTTPS, FTP, SFTP, SSH, SCP, SYSLOG, SNMP, TIME, TELNET - Alert-Notification system of status change by Email, WinMail, SNMP or an external connected display - Full SNMP v1,v2,v3 support with own SNMP-daemon for status and configuration and SNMP Trap messages USB Port for installing firmware updates, locking frontpanel menu access and backup/restore of configuration and log files Meinberg GPS Antenna/Converter Unit connected with up to 300m of standard coaxial cable RG58

**LANTIME M300: NTP Server in 1U Case for Server Rackmount** The Meinberg LANTIME M300 time server provides accurate time to networks of any size. It synchronizes all NTP- or SNTP-compatible systems. The M300 time server uses as a reference time source either any compatible external or built-in Meinberg reference clock (Stratum 1 mode) or up to 7 NTP servers (Stratum 2 mode). A large display shows the state of the NTP subsystem. The configuration of the system can be done by using a standard web browser to access the extensive but straightforward html interface. Alternatively a text based and menu driven setup utility can be started from the shell prompt after logging into the unit via Telnet or SSH. Because of its modular system architecture it is possible to equip this LANTIME time server with up to six ethernet ports, even fiber optic network ports and one or three Gigabit Ethernet ports are available as an option. **Key Features**: - Selectable Reference Time Sources: -GPS: Satellite receiver for the Global Positioning System -GNS: Combined GPS/GLONASS/Galileo/BeiDou satellite receiver (L1 frequency band), can also be used for mobile applications -PZF: DCF77 correlation receiver for middle europe -MSF: Long wave receiver for Great Britain -WWVB: Long wave receiver for the US time signal -TCR: Time code receiver for IRIG A/B, AFNOR or IEEE1344 codes -MRS: (GPS, PPS, 10MHz, NTP): Multi Reference Source - several reference sources, adjustable following priority of signal -RDT: (external PPS or NTP): Time Server without internal receiver module - Synchronization of NTP and SNTP compatible clients - Web-based status and configuration interface (Demo) and console-based graphical configuration utility - Supported net protocols: IPv4, IPv6, NTP, (S)NTP, DAYTIME, DHCP, HTTP, HTTPS, FTP, SFTP, SSH, SCP, SYSLOG, SNMP, TIME, TELNET - Alert-Notification system of status change by Email, WinMail, SNMP or an external connected display - Full SNMP v1,v2,v3 support with own SNMP-daemon for status and configuration and SNMP Trap messages - USB Port for installing firmware updates, locking frontpanel menu access and backup/restore of configuration and log files - Meinberg GPS Antenna/Converter Unit connected with up to 300m of standard coaxial cable RG58 - Meinberg's LANTIME time server is available with a variety of additional output options: IRIG Time Code, frequency synthesizer and programmable pulse outputs illustrate some of the many expansion options for your NTP server - Two (standard) or optional up to six independant RJ-45 ethernet interfaces 10/100 MBit

**LANTIME M600/MRS/PTP: PTPv2/IEEE 1588-2008 Ordinary Clock and NTP Time Server synchronized by GPS/GLONASS/1PPS/10MHz/IRIG/NTP/PTP** Meinberg LANTIME time servers are used around the world to provide accurate time to networks of any size. The LANTIME M600/MRS/PTP synchronizes all systems that are PTPv2, NTP- or SNTP-compatible. It uses a built-in Meinberg GPS receiver or combined GPS/GLONASS clock and supports a broad range of other reference time sources like 1PPS, 10MHz, IRIG time codes (both DCLS and AM) or upstream NTP servers. The built-in PTP unit can be configured to act either in master or slave mode. Therefore it is possible to use IEEE-1588 PTP as an additional input reference for the MRS engine. The appliance is a perfect solution to measure and compare the different reference time sources against each other. A highly stable and precise oscillator is capable of bridging interferences or a temporary loss of reception and can also be used as a stable independent time base when operated in free running mode. **Key Features**: - Synchronization of IEEE1588-2008 (PTPv2) compatible clients - Supported PTP Profiles: - Default E2E IEEE 1588-2008 - Default P2P IEEE 1588-2008 - ITU-T G.8265.1 Telekom Profil - IEEE C37.238-2011 Power Profil - AES67 Media Profile - Accepts a large number of sync references: GPS, 1PPS, 10MHz, IRIG (DCLS and AM), PTP and NTP - Synchronization of NTP and SNTP compatible clients - Web-based status and configuration interface (Demo) and console-based graphical - configuration utility - Supported net protocols: IPv4, IPv6, PTP/IEEE 1588-2008, NTP, SNTP, DAYTIME, DHCP, - HTTP, HTTPS, FTP, SAMBA, SFTP, SSH, SCP, SYSLOG, SNMP, TIME, TELNET, W32TIME - Alert-Notification system of status change by Email, WinMail, SNMP or an external connected display - Full SNMP v1,v2,v3 support with own SNMP-daemon for status and configuration and SNMP Trap messages - USB Port for installing firmware updates, locking frontpanel menu access and backup/restore of configuration and log files - Meinberg GPS Antenna/Converter Unit connected with up to 300m of standard coaxial cable RG58 - Six independent RJ-45 ethernet interfaces 10/100 MBit (incl. 1 x IEEE 1588-2008)

**Netally-EtherScope nXG Portable Network Expert** The Netally-EtherScope nXG Portable Network Expert is a Multi-technology, all-in-one handheld network analyzer that enables engineers and technicians to get more done faster, from deployment to maintenance and documentation of their ever-changing Wi-Fi, Bluetooth/BLE, and Ethernet access networks. **Features** - Install, test, verify, and troubleshoot technology upgrades, NBASE-T, 10G, Bluetooth/BLE, and Wi-Fi 6/6E networks with advanced Android™-based troubleshooting apps and purpose-built test hardware - Verify up to 10G Ethernet link performance for critical servers, uplinks and key end devices, and validate Wi-Fi network performance - Empower technicians who may not have access to network management systems or other engineer-level tools to assess and document complex network deployments with multiple VLANs and Wi-Fi SSIDs - Faster and easier Wi-Fi site and Bluetooth/BLE surveys with AirMapper™ Site Survey including active surveys to validate client experience and roaming. Create and share visual heatmaps of key performance metrics in the Link-Live Cloud Service. (AllyCare Premium Care Support required for certain mapping functions.) - Automatically discover and instantly map your wired and Wi-Fi networks in Link-Live; speeds troubleshooting and keeps network documentation up-to-date. Exports to Visio. - Seamlessly consolidate and manage field test data, and integrate with network management systems via Link-Live™ collaboration, reporting, and analysis platform **Product Video**

The VeEX MTX150x is a fully-integrated and self-contained Ethernet services test solution for Layer 1-to-4+ applications and Fibre Channel (SAN). This rugged and ultra-portable field hand-held test set can be configured with interfaces and technologies required by field technicians to install, verify, maintain and troubleshoot Metro Ethernet links, Business services, Internet Access and other packet-base services up to 10 Gbps. Its native support for 2.5G/5G/10GBASE-T reduces cost of ownership. **The VeEX MTX150x 10G Ethernet Tester supports**: - The smallest full-featured Ethernet solution on the market with native RJ45 1G/2.5G/5G/10GBASE-T and 1G/10GBASE-X support. No adapters required - Dual port operation up to 10 Gbps - Optimized for field technicians installing, verifying, troubleshooting and maintaining Carrier Ethernet, Metro, Access, Business Services, and Storage Area Networks, as well as fiber, backhaul, microwave links. - Robust, handheld chassis packed with powerful and flexible features for demanding environments and test conditions - Flexible hardware configuration to meet each application’s requirements and reduce CAPEX - Field upgradeable licenses to optimize OPEX - Test set connectivity via micro-B USB and optional built-in Wi-Fi and Bluetooth® wireless interfaces; USB-A and 10/100BASE-T are also available via OTG cables - VeSion R-Server asset, workflow and results management - Remote access and control via Web Browser, VNC® client and ReVeal PC software. Compatible with VeEX EZ Remote collaboration services. - User defined test profiles and thresholds enable fast, efficient and consistent turn-up of services - Fast and efficient test result transfer to USB memory stick - Li-ion battery pack for extended field testing autonomy

VeEX® RXT is the industry’s most flexible, compact, and future- proof hand-held test solution for core, metro and access. The RXT-6200 module adds 100 GE Ethernet, 5G/4G Mobile Backhaul and Fronthaul, Storage Area Networks, OTN, SDH/SONET, PDH/T-Carrier links and services testing, from 1.5/2 Mbps up to 100 Gbps. **The VeEX RXT-6200 100G Universal Module supports**: - Optical 100 Mbps to 100 Gbps Ethernet testing, including 25GE and 50GE - Electrical 10 Mbps to 10 Gbps Ethernet testing - Electrical 10 Mbps to 10 Gbps Ethernet testing - BERT and Throughput testing at Layer 2 and Layer 3 - RFC2544 and V-SAM (Y.1564) testing - SDH/SONET Testing - PDH/T-Carrier Testing - OTN Testing - Fibre Channel up to 32 G